How to install the electric heater in 4 steps?

If you want to enjoy hot water in your home, you should consider In installing an electric water heater . In the Jaafar Shop blog Today we will explain it to you with very simple instructions How to install an electric water heater .

In case you need hot water urgently, we recommend that you hire a professional. It can take an expert about an afternoon to install an electric water heater. Otherwise, a person who does not have much knowledge of the topic could take up to 6 hours.

If you have basic knowledge, follow these steps to install an electric water heater and enjoy its features:

Steps to install an electric water heater in your home

Close the shut-off valve to secure the heater

Before you start installing an electric water heater, you must close the water valves that connect to the place where you will place it Geyser . If you do not have split valves, which is most likely You must close the stopcock General water in your home.

If you do not choose where to install the electric water heater, you can do it in the kitchen or in the bathroom. You should check that where you are going to install the electric water heater, there is a plug with a ground connection and close to the water inlet. The hot and cold water connection should be as close as possible to the thermos.

When you choose the place, you should also keep in mind that you should hang the thermos. So you need a wall to support the weight. If you have a water heater Electric with capacity of 50 litres, 30 litres, or 15 litres Most walls will do.

The most recommended thing is that before purchasing the heater , you have already chosen where you will install it. This way it will be easier to decide to buy Horizontal electric water heater Or heater Vertical electric water .

Drill the holes you need to install the electric water heater

Before drilling holes, you should measure the distance between the anchor legs horizontally and vertically. This way you will make a mark on the wall where the screws should be placed.

Once you are sure of the places you want to make the hole, you can start drilling and inserting the plugs. These must be at least 10 mm thick and must be accompanied by their own nuts and washers. For safety and regardless of the shape of the wall, we recommend performing the installation with chemical plugs, especially when it comes to heaters From 50 litres.

Remember to check with the level that the holes are straight. This way, you will be sure that your electric water heater will not tilt to any side.

Electric water heater stuck

To comment Hot and cold water heater We recommend that you seek help. It is not a difficult task but these machines are usually very heavy and so having a helping hand is ideal to avoid accidents. Next, you need to install the mounting nuts on the stabilizer rod shank.

Connect the water to your electric water heater

Place the two electrolyte-resistant handles on the hot and cold water threads at the base of the thermos. You will then attach the safety valve to the cold water inlet. This way you will protect it from excessive pressure.

We recommend wrapping Teflon tape or hemp twine around the strings to seal them and prevent leaks.

Next, you should connect the reinforced hoses to the safety valve of the cold water inlet and the electrolyzer at the hot water outlet. Finally, you will connect the hoses to the square keys of the thermos.

At this point, you have finished installing the electric water heater. However, you should check its correct operation and check for leaks. Before doing this, you must remove air that may have entered the installation.

How do I remove air from a circuit? Geyser Water composition?

Before testing the electric water heater installation Horizontal Or vertical, you should get rid of the air that may have been filtered. To clean it, you should open the cold water inlet tap and then open any hot water tap so that the air is expelled while the thermos is filling.

Once the air is eliminated efficiently, you can start your thermos without problems.

When is the electric heater changed for another?

Did the heater break down? Did you decide to change the electrician because it does not meet the basic needs of your home? If so, you should keep in mind Installing an electric water heater . However, this task requires a lot of care and some basic knowledge for everything to work perfectly.

If this is your case, the first thing you should do is dismantle the old heater or Electric heater . To do this, you must close the connected water valve or the general disconnect of your home.

After that, the heater must be emptied completely. This is very easy to do. First, you have to close the cold water inlet valves and the hot water outlet valve. The next step is to disconnect the hoses from the thermos. Finally, you connect a hose to the hot water outlet of the thermos, disassemble the safety valve and gravity, the thermos empties itself.

When you turn down the heater You can start from Step 3 to install your new electric thermos if you haven't thought about moving it.

Remember, the best thing you can do for electric water heater installation is to hire experts and people with experience in the task. This will ensure that everything works perfectly, the water heater will not be damaged due to poor installation, you will avoid accidents and will not spend a long time operating the electric water heater in your home.